Friday 16 October 2015

Transom framing

With the main cabin nearing completion I had moved all the accumulated tools and materials into the cockpit. Seeing I had them all there, I decided it was time to get serious about closing off the cockpit which will be a milestone of sorts for me.

Just as I did with the cockpit floor I sealed the edge of the seats to the hull with wood and later carefully epoxy filleted them.



At the rear of the cockpit is a storage locker for smelly items (stove fuel, cheap camping stove and gas bottle, paint etc) that you don't want to allow the fumes from into the cabin.  It will drain into the cockpit and then out through the transom.  Below shows me constructing it from three pieces of ply, with doubler on top for an access hatch.


And from underneath with wood to screw the hatch into:


Below after the epoxy set.  The hatch is just sitting there and the front is yet to be trimmed.  It was also not glued to the supporting beams so I could remove it for further work in the cockpit until closer to transom fitting.


After removing the smelly locker lid I dry fit the transom laminated beam (further most one) and the quarter deck front beam.



I marked out notches for a 90mm x 20mm hardwood king plank, and epoxied it all in place.  The other wood each side of the king plank is just to hold the beams in place until the epoxy set.



Below is the final result, this will have two layers of 6mm ply on top once the transom is in place to complete the deck.  Love the curves!



A final shot from outside looking across the transom support frame (Frame #10).  I dusted off the electric plane and took the hull edges back flush with the frame, next is to dry fit the transom and finally complete the main cabin!




Main cabin crawls on

Again I have let the team down with updates, my only excuse is that I don't feel like I have much to show for the work I've done!  My kids were also on school holidays, so lots of motorbike riding and activities non-boat related.  Managed to slip in a few days in Tasmania, somewhere definitely I want to spend more time. I would like to make it to the wooden boat festival in 2019 maybe, it is on every two years in Hobart.

The main cabin has taken most of my time, but I am happy with progress to date and it is almost finished. Before I could paint the main cabin I had to finish some final construction.  Below you can see the inside of the front of the cabin.  In the middle from left to right run the deck beam (bottom) the deck (2 x 6mm ply) and on top another laminated beam.  You can see a vertical bolt holding all the beams together, and one running horizontal through the beam, 12mm ply doubler then cabin front (there is another 12mm doubler on the outside as well).



 Below is the cabin side (2 x 9mm ply) which goes down as far as the carlins for the side decks.



 The deck beams were covered with a ply strip matching the curve, this also leaves a space about 45mm wide which will catch any condensation that runs down the cabin sides.  Below is the cabin front in the galley.



On the cabin sides I screwed timber underneath the carlins to cover the ply cabin side ends, leaving 20mm out into the cabin.


Resting on top of this I stood a piece which I had cut/sanded on an angle at the top.  This was screwed from below up through both pieces and clamped onto the cabin side with glue.


Below is what it looks like from a distance, this provides a hand hold to grab onto as you move about and will also act to catch condensation and prevent drips onto the seats/berths in the main cabin.  I cannot claim the credit, it was in the John Welsford plans!


A closer shot on an angle showing the hand hold/drip catcher.  There will be port holes above these on both sides of the cabin down the track.


I also put some dressing timber edge on the end of the galley, filled screw holes and sanded surfaces.



Below is where the head/desk is pre painting:


And the main cabin storage areas:



Final step was coating the cabin sides and roof with a couple of coats of epoxy wet on wet. Below are the cabin side and some of the roof, including curved beam:



I was getting ready to paint looking around and thought I liked the look of the epoxied ply.  I was thinking of leaving the cabin sides and roof exposed, but it felt like a bit much.  Compromise was the two cabin sides which will have port holes and the laminated curved beam.  I taped up the edges and gave the whole lot a coat of oil based sealer/undercoat.  If you look closely you can just make out the tape between the epoxied ply and the painted bits.


And looking forward including the cabin roof:

Then it was two coats of water based exterior house paint, including the doors to the storage lockers:

And other bits and pieces including the pieces of the desk:


Once it was done I peeled off the tape and attached the doors to the storage lockers.  Once in place I added catches inside and brass handles.  Below is starboard looking forward, ignore the toilet it is just sitting there while I fit the desk and seat to hide it!


Below is the port side with the galley to the right out of shot:


And the galley with the sink in place and hand pump fitted.  The black fitting will allow filling of the water tank in the cassette toilet without trying to climb under the galley.  Bottom right is the start of fitting the gimbals for the spirit stove.  It is two burner and will face the sink, parallel to the centre line.



Still some fit out to do in the head/desk and galley but getting there.